John Deere sku23045 44 snow blower fits X Series

John Deere 44 inch snow blower fits X Series garden tractors. It has some scratches and minor surface rust from use but its still shiny and works like new. All of the needed hardware, linkage, brackets and owners manual are included for installation with the exception of the "spring assist", this was never needed or used and has been misplaced but it still works quite well as is. The advertisement is just for display purposes, please review all of the loaded pictures to see the actual snow blower's condition. It comes as shown but does not include the tractor.

(112-cm) Snow Blower on X324 Tractor. (112-cm) Snow Blower has the capacity to handle big snow removal jobs.

This snow blower works well in all snow conditions and is suited for snow removal around recreational parks, industrial parks, and other applications where snow must be moved greater distances. Two-stage design is ideal for home and estate owners in heavy snow regions. Two-stage snow blower is more effective than a single-stage snow throwers when operating in wet, heavy snow and deep snow conditions. The low-speed auger sizes crusted material as it moves snow toward the second-stage blower. Chute provides consistent snow placement in variable snow conditions because the high-speed blower gives the discharged snow consistent velocity, even in very light clean-up volumes.

The optional brush guard or bumper can remain on the tractor when using the snow blower. The low-speed auger picks up snow and moves it toward the center of the machine into the high-speed rotor where it is blown out of the discharge chute. A cast-iron gearbox provides speed reduction for the auger and is protected by shear bolts for each auger half. Two-stage snow blowers are more effective than single-stage snow throwers when operating in deep snow as the low-speed auger is used to size crusted material.

They also provide consistent snow placement in variable snow conditions because the high-speed rotor gives the discharged snow consistent velocity-even in very light clean-up volumes. The second-stage blower fan is formed from the same durable and rust-resistant, ultra-high molecular weight (UHMW) polyethylene material proven in the Power Flow. Blower fan for durability and long life.

The durable fan material has the same durable cold-weather characteristics as that used in snowmobile track rollers and will not bend and cause the fan to get out of balance. The discharge spout and deflector are made from high-density polyethylene material that will not dent or rust and resists snow buildup to ensure trouble-free operation. It is more durable, especially in cold-weather use, than the polypropylene material used by some other manufacturers. Spout direction and deflector angle can both be conveniently controlled from the operator station.

The chute material remains smooth and is less likely to clog than a steel chute. Controls to operate the chute are conveniently located for easy operation.

The discharge spout can be rotated 200 degrees from the operator station. The deflector can be easily adjusted from the operator's station to determine distance of throw. Skid shoes help control the height of the snow blower cutting edge and are especially helpful for use on gravel drives and irregular surfaces. Skid shoes can be adjusted by loosening the mounting bolts and positioning them to suit the operating conditions. Securely held in place by three bolts.

Can be adjusted for rough or smooth surface conditions. The snow blower slips over and locks onto the front hitch with attached snap pins. Fast and easy installation with no tools or loose parts. Hitch provided with the snow blower. Optional bumper or brush guard can remain on the tractor with snow blower installed. Heavy-duty in-line belt and gearbox drive. Dependable in-line belt drive (belt colored red). In-line drive belt for efficient transfer of power and dependable operation.

Spring-loaded idler pulley keeps belt at the optimum tension. Durable cast-iron right-angle gearbox drives the blower and also provides power to the auger.

Height to top of housing. (12.1 cm x 35.6 cm). Ultra high molecular weight (UHMW) polyethylene.

100 degrees to each side. (19-mm) sealed bearings on each end. Shear bolt for each auger half. Optional for both sides of housing.

Spring-assisted foot lift or hydraulic lift (X310, X360). 180 lb (81.6 kg). No tools required; 5 minutes. (112-cm) Snow Blower is compatible with the following. Select Series X300R, X300, X304, X310, X320, X324, X340, X360, X500 M-T, and X520 M-T Tractors. X300R Rear-Discharge Tractor (see DTAC solution 79224 for snow blowers manufactured before spring 2008, serial numbers 030,000 and below). AM136646 lift-assist spring kit is not compatible with tractor models equipped with hydraulic lift as standard equipment.

(122-cm) mower (BM21848): below serial number -M0X320A040168. X320 less mower (BM22336): below serial number -M0X320A040168.

X320 less mower, export (BM21862): below serial number -M0X320B040377. (122-cm) mower (BM21849): below serial number -M0X324A040092. (137-cm) mower (BM21850): below serial number -M0X340A045012. (122-cm) mower (BM21851): below serial number -M0X500A020104. (137-cm) mower (BM22128): below serial number -M0X500C020001. X500 less mower (BM22338): below serial number -M0X500C020001. (122-cm) mower (BM21855): below serial number -M0X520A020008.

X350R requires adjustable spring-assist kit for snow blower use. For rear ballast, the following is recommended.

For X300 Series Tractors, two 42-lb (19-kg) Quik-Tatch weights are recommended for additional traction. For X500 M-T and X520 M-T Tractors, two 50-lb (23-kg) rear-wheel weights (one on each wheel) or up to four 42-lb (19-kg) Quik-Tatch weights are recommended for additional traction. Tire chains are recommended for traction.

Winter grille cover is recommended for tractors with air-cooled engines to prevent carburetor icing. Optional drift knives are available for each side of the blower housing and are recommended for deep-snow conditions.

Optional heavy-duty skid shoes are available for high-hour use and extra protection. Optional plastic skid shoes are available for reduced scratching and marring of driveway surfaces. It does come with a guarantee to be as described. The item "John Deere sku23045 44 snow blower fits X Series" is in sale since Wednesday, December 16, 2020. This item is in the category "Home & Garden\Yard, Garden & Outdoor Living\Lawn Mowers, Parts & Accessories\Lawn Mower Accessories".

The seller is "bleubarracuda" and is located in Timberville, Virginia. This item can't be shipped, the buyer must pick up the item.

• Brand: John Deere
• Type: Two Stage
• Compatible Brand: For John Deere
• Clearing Width: 44 in